DMS-S605_product
DMS-S605_dims

Inertial Measurement System DMS-S605

This inertial measurement sensor provides bank and elevation attitude output along with leveled accelerometer outputs in a small hard-mountable housing.

Features:

  • Solid State, Strapdown System
  • Six Accelerometer Outputs
  • Small Size
  • Low Cost, Low Power
  • Rugged, High Reliability
  • Analog and RS-232 Serial Outputs
  • One Year Limited Warranty
  • Engineering Support

Request a Quote

SKU: DMS-S605 Categories: ,

Product Description

Originally developed to meet the needs of automotive testing professionals, the Dynamic Measurement System (DMS) was designed for instrumenting the drive and handling characteristics of vehicles. The DMS may be used in almost any application where triaxial angular rate and acceleration data is required. The sensor provides both angular rate and acceleration outputs in analog and digital formats.

The DMS features six accelerometer outputs. The X, Y, and Z axis outputs represent the accelerations in the plane of the vehicle body, while the second set of three outputs measure the acceleration aligned with an earth-level coordinate system. This allows forward and lateral acceleration measurements that are essentially free of gravity influences. The triaxial sensor set allows software alignment of sensors, greatly reducing any alignment errors. The serial interface is highly configurable and provides access to almost all operational parameters.

The DMS-S605 is a miniaturized version of the DMS-E604. This sensor uses MEMS gyros to make the instruments smaller and more economical. The E-series line of sensors uses our larger  gyros for enhanced accuracy and signal stability.

The DMS uses an input of forward velocity to compensate the long term references, allowing the error correction system to work continuously. Other companies manufacture sensor packages that turn off their corrections during high dynamic conditions causing a drift in accuracy over time. The DMS-S605 is much more useable in highly dynamic conditions, and has been designed to provide the best possible combination of reliable data and low cost.

DMS-S605 is useful for automotive testing and land vehicle dynamics applications.

Applications

Downloads

Download Spec Sheet (PDF - 40.6 KB)

 

Download Manual (PDF - 146.1 KB)

 

Specifications

Attitude

Range: Bank ±180°
Range: Elevation ±90°
Resolution: 0.02° Binary mode (14 bit)
Analog Scale Factor: 18°/V ±10V Bank; ±5V Elevation
Accuracy: Static ±0.5°
* Accuracy: Dynamic ±2%

Relative Heading

Range: 0° – 360°
Resolution: 0.02° Binary mode (14 bit)
Analog Scale Factor: 18°/V ±10V Output
* Accuracy: Dynamic ±2%

Angular Rate

Range: Roll, Pitch, Yaw ±100°/sec
Resolution: 0.025°/sec Binary mode (14 bit)
Analog Scale Factor: 10°/sec/V ±10V Output
Scale Factor Accuracy: 2%
Bias: Roll, Pitch, Yaw < 0.3°/sec
Non-Linearity: < 0.05% Full scale range
Bandwidth: 20 Hz

Acceleration

Range: X, Y, Z ±10g
Range: Fwd, Lat, Vert ±10g
Resolution: 4mg
Analog Scale Factor: 1g/V ±10V Output
Scale Factor Accuracy: 1%
Bias: X, Y, Z < 10mg
Non-Linearity: 0.1% Full scale range
Bandwidth: 3 Hz

Environmental

Temperature: Operating -40°C to +85°C
Temperature: Storage -55°C to +85°C
Vibration: Operating 2.5g rms 20 Hz to 2 KHz
Vibration: Survival 10g rms 20 Hz to 2 KHz
Shock: Survival 500g 10mS ½ sine wave

Electrical

Frame Rate: 71.1 Hz Maximum
Startup Time: Data 5 sec
Startup Time: Fully operational 10 sec
Input Power: 10 to 30VDC 2.7W
Input Current: 225mA @ 12VDC 112mA @ 24VDC
Input Velocity: (Optional) ±10VDC Full scale (±400kph)
Digital Output: RS-232
Analog Output: ±10VDC
Analog Output Impedance: 300 Ohm Per line

Physical

Axis Alignment: < 0.25°
Size: Including
Mounting Flanges
3.24″W x 5.78″L x 3.50″H 8.2 x 14.7 x 8.9 (cm)
Weight: 23oz (1.4lb) 650 grams (0.7Kg)
Connection: RS-232 9 pin female “D” subminiature
Connection: Power /
Analog Outputs
25 pin male “D” subminiature
* Assumes accurate velocity data.
Actual accuracy can be calculated as the listed percentage multiplied by the change in value over the entire dynamic maneuver.
Specifications are subject to change without notice.
This product may be subject to export restrictions. Please consult the factory.

Additional Information

Weight 0.7 kg
Dimensions 14.7 x 8.2 x 8.9 cm

Reviews

There are no reviews yet.

Be the first to review “Inertial Measurement System DMS-S605”

Your email address will not be published. Required fields are marked *

This blog is kept spam free by WP-SpamFree.