Inertial Measurement System DMS-EGP01 (Single Antenna GPS)

The DMS-EGP01 is a higher accuracy single antenna GPS enabled AHRS. It uses gyros with lower bias and noise characteristics for more accurate attitude outputs.

Features:

  • Solid State, Strapdown System
  • GPS Velocity Data
  • Latitude, Longitude, Altitude Output
  • Low Cost
  • Rugged, High Reliability
  • Vibration Resistant
  • Analog and RS-232 Serial Outputs
  • Two Year Limited Warranty
  • Engineering Support

Request a Quote

SKU: DMS-EGP01 Categories: , ,

Description

Originally developed to meet the needs of automotive testing professionals, the Dynamic Measurement System (DMS) was designed for monitoring the drive and handling characteristics of vehicles. The DMS may be used in almost any application where triaxial angular rate and acceleration data is required. This inertial sensor provides both angular rate and acceleration outputs in analog and digital formats. The DMS features six accelerometer outputs. The X, Y, and Z axis outputs represent the accelerations in the plane of the vehicle body, while the second set of three outputs measure the acceleration aligned with an earth-level coordinate system. This allows forward and lateral acceleration measurements that are essentially free of gravity influences. The triaxial sensor set allows software alignment of sensors, greatly reducing any alignment errors. The serial interface is highly configurable and provides access to almost all operational parameters.

The DMS-EGP01 is used primarily in vehicle applications to integrate the features of a DMS-E604 and a velocity sensor into one unit. This sensor is equipped with a single GPS antenna that provides vehicle velocity data to the DMS. This data enhances the unit’s performance during highly dynamic maneuvers such as sharp turns and also makes this inertial gyro sensor a more complete system since it does not require velocity information to be supplied from an external sensor.

The DMS-EGP01 is typically used in automotive testing and vehicle dynamics applications. This sensor operates as an enhanced DMS-E604. The GPS antenna provides the DMS with a velocity signal, and also transmits heading data while in motion.

Applications

Downloads

Download Spec Sheet (PDF - 97.8 KB)

 

Download Manual (PDF - 173.0 KB)

 

Specifications

Attitude

Range: Bank ±180°
Range: Elevation ±90°
Resolution: 0.02° Binary mode (14 bit)
Analog Scale Factor: 18°/V ±10V Bank; ±5V Elevation
Accuracy: Static ±0.25°
* Accuracy: Dynamic ±0.5%

GPS Heading

Range: 0° – 360°
Resolution: 0.02° Binary mode (14 bit)
Analog Scale Factor: 18°/V ±10V Output
Accuracy: Static ±0.5° (±0.05°/sec
stationary)
Relative, based
on gyro drift
* Accuracy: Dynamic or Relative ±0.5%

Angular Rate

Range: Roll, Pitch, Yaw ±100°/sec
Resolution: 0.025°/sec Binary mode (14 bit)
Analog Scale Factor: 10°/sec/V ±10V Output
Scale Factor Accuracy: 0.5%
Bias: Roll, Pitch, Yaw < 0.2°/sec (Analog) ±0.02°/sec
Binary mode (14 bit)
Non-Linearity: < 0.1% Full scale range
Bandwidth: 20 Hz
Noise: < 0.03°/sec rms

Acceleration

Range: X, Y, Z ±10g
Range: Fwd, Lat, Vert ±10g
Resolution: 4mg
Analog Scale Factor: 1g/V ±10V Output
Scale Factor Accuracy: 1%
Bias: X, Y, Z < 10mg
Non-Linearity: 0.1% Full scale range
Bandwidth: 3 Hz

GPS Positioning

Range: Latitude ±90°
Range: Longitude ±180°
Range: Altitude 0ft to 21500ft
Resolution: Lat, Long 0.0000013° Binary mode (28 bit)
Resolution: Altitude 2 ft
Accuracy: Lat, Long 1.5m rms

Environmental

Temperature: Operating -40°C to +85°C
Temperature: Storage -55°C to +85°C
Vibration: Operating 5g rms 20 Hz to 2 KHz
Vibration: Survival 10g rms 20 Hz to 2 KHz
Shock: Survival 500g 10mS ½ sine wave

Electrical

Frame Rate: 71.1 Hz Maximum
Startup Time: Data 5 sec
Startup Time:
Satellite acquisition
5 min Typical
Input Power: 10 to 30VDC 5.5W
Input Current: 458mA @ 12VDC 229mA @ 24VDC
Input Velocity: (Optional) ±10VDC Full scale (±400kph)
Digital Output: RS-232
Analog Output: ±10VDC
Analog Output Impedance: 300 Ohm Per line

Physical

Axis Alignment: < 0.1°
Size: Including
Mounting Flanges
6.5″W x 6.5″L x 3.1″H 16.5 x 16.5 x 7.9 (cm)
Weight: 52oz (3.2 lb) 1470 grams (1.5 Kg)
Connection: RS-232 9 pin female “D” subminiature
Connection: Power /
Analog Outputs
25 pin male “D” subminiature
Connection: Antenna SMA Antenna cable length: 3.0m
* Using velocity data with GPS mode on.
Actual accuracy can be calculated as the listed percentage multiplied by the change in value over the entire dynamic maneuver.
Acquisition time for GPS units is typical for the contiguous United States. Acquisition time may differ due to interference in your geographic area.
Specifications are subject to change without notice.
This product may be subject to export restrictions. Please consult the factory.

Additional information

Weight 1.5 kg
Dimensions 16.5 x 16.5 x 7.9 cm

Reviews

There are no reviews yet.

Be the first to review “Inertial Measurement System DMS-EGP01 (Single Antenna GPS)”

Your email address will not be published. Required fields are marked *

This blog is kept spam free by WP-SpamFree.